-
- Advertisement
4JB1 Engine bolt Pattern
4 posts
• Page 1 of 1
4JB1 Engine bolt Pattern
by flatlander07 » Sun Mar 14, 2010 11:12 am
Does anybody have dimensional data on the 4JB1 engine bolt pattern, where the bell housing bolts up?? I've heard it's the same as the 223, and maybe the 3.1.
- flatlander07
- Isuzu Baby
- Posts: 7
- Joined: Sat Mar 13, 2010 10:45 am
- Age: 53
- Country: USA
- City: Frankfort
- Vehicle: Dodge 2002 4WD Dakota with 4JB1TC engine
Re: 4JB1 Engine bolt Pattern
by geeves » Sun Mar 14, 2010 5:35 pm
4jb1 is same as 4jg2 but not c223
Sanding your knuckles before starting work can help. That way you cant skin them
-
geeves - Site Admin
- Posts: 8964
- Joined: Sun May 10, 2009 1:36 pm
- Location: Rangiora
- Age: 63
- Country: NZ
- City: Rangiora
- Vehicle: 94 bighorn 4jg2
2013 Subaru XV
Re: 4JB1 Engine bolt Pattern
by flatlander07 » Mon Mar 15, 2010 6:25 am
Geeves...
Ahhhh. That's interesting. My profile says I have the diesel Dakota, but still haven't got it going yet.
Over here out in California, an adapter plate shop was supposed to be making me a plate, but just can't get to it.
Mopar Racing gave me the Dodge bellhousing bolt hole and dowell pin hole locations, with an excellent drawing. I actually have a machine shop for my ptostumpgrinders.com.
If I had the Isuzu drawing of the "back" of the motor, I could do my own adapter.
It just hit a year and a half waiting for this busy swamped shop to do my little one off special. If you know where I could find the hole location drawing, even like an SAE flywheel housing drawing (that showed the engine side) would get me there.
Thanks so much for the resource.
Jeff
Ahhhh. That's interesting. My profile says I have the diesel Dakota, but still haven't got it going yet.
Over here out in California, an adapter plate shop was supposed to be making me a plate, but just can't get to it.
Mopar Racing gave me the Dodge bellhousing bolt hole and dowell pin hole locations, with an excellent drawing. I actually have a machine shop for my ptostumpgrinders.com.
If I had the Isuzu drawing of the "back" of the motor, I could do my own adapter.
It just hit a year and a half waiting for this busy swamped shop to do my little one off special. If you know where I could find the hole location drawing, even like an SAE flywheel housing drawing (that showed the engine side) would get me there.
Thanks so much for the resource.
Jeff
- flatlander07
- Isuzu Baby
- Posts: 7
- Joined: Sat Mar 13, 2010 10:45 am
- Age: 53
- Country: USA
- City: Frankfort
- Vehicle: Dodge 2002 4WD Dakota with 4JB1TC engine
Re: 4JB1 Engine bolt Pattern
by BUSHPIG » Mon Mar 15, 2010 3:02 pm
im pulling my box soon to swap for a 3.1 box if you still need a drawing with hole spaceing ect. ill mesure it up n let u know
-
BUSHPIG - Isuzu Senior
- Posts: 196
- Joined: Fri Jun 05, 2009 8:47 pm
- Location: Crappy Old Auckland
- Age: 29
- Country: NewZealand
- City: Auckland
- Vehicle: 1988 GQ Safari
TD42 Turbo Running 17psi
Custom BRD Top Mount Intercooler
Custom BRD 3" Exhaust
Factory GU Turbo Airbox
Safari Snorkle
2000 Gu Td42-T Injector Pump
Turbo Injectors
Pto Winch
Custom BRD On-Board Air Bracket With Modified Second A/c Pump
Custom Front Bar Work
Ally Roof Cage
2 1/2" Suspension Lift
Front LSD
Rear LSD
33x12.5xr15 Maxxis Tyres
Diff And Gearbox Breathers
Am Cb
Uhf Cb
GPS Tracker.
Planed Mods::
Exo Cage
Rear Barwork
Rear 14,000lb Winch
4 posts
• Page 1 of 1
Return to General Isuzu and 4x4 discussion
Who is online
Users browsing this forum: No registered users and 6 guests